Boarding Up Windows And Doors Techniques To Simplify Your Everyday Lifethe Only Boarding Up Windows And Doors Trick That Everybody Should Be Able To > 자유게시판

Boarding Up Windows and Doors Before a Storm Hits

Insuring your windows and doorways before an event can give you an effective protection against damage. To do this, you should have a few things in your desk.

Find the width and height of the window, including the frame (not the trim or the masonry around the window). Write these measurements down so you don't forget them.

Preparation

It is recommended to cover your windows and doors before an event like a hurricane or natural disaster. This will help prevent damage to property and reduce the loss of life. boarding up commercial property up windows requires an extensive amount of preparation, such as purchasing and measuring plywood boards, and determining the exact dimensions of each window to be covered. It takes time to cut and put in the boards in a proper manner. The process can be streamlined by beginning the preparations immediately you hear of an approaching storm. You can avoid a stressful rush at the last minute and make it simpler for you and your employees.

Begin by listening to weather forecasters and observing the guidelines of your local government. The earlier you start the process, the better, as it gives you enough time to collect and store the needed materials without feeling pressured by a rapidly approaching storm. You may need a large amount of plywood to cover your windows depending on the severity and speed of the storm. To ensure that you have the right size, make use of a tape measure to determine the width and height of each window opening. Make sure to include the framing or trim around each window, as well as any ledges with extended edges if they are necessary.

Divide the width and height of your window by 2 to determine the amount of plywood sheets that you will need. For example, if width of your window is 16 inches the thickness of each sheet should be 8 inches. If your exterior is made of wood drill pilot holes into the plywood sheet to align with the window frame below. This will reduce the possibility of splitting when you screw in the screws.

If you have a bigger window opening than one sheet of plywood is able to handle cut two sheets plywood that are each half as large as the window you wish to cover. Then, place them side by side on the wall. Cut a piece of 2 by 4 in (5.1 x 10.2 cm) of lumber to the length the connecting edge between the plywood sheets and then place it on the top of the seam. Then you can drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure security and safety, only use materials that are durable and won't break or splinter in strong winds. The most common material used to encase windows is plywood, which is cheap easily available and simple to work with. Choose plywood that is of the exterior grade (CDX), as it is more durable and contain fewer warps and knots. A sturdier option is storm shutters, also known as hurricane shutters, which are erected over windows already in use to offer greater protection against shattered glass and inclement weather.

Once you've identified the position of the window openings, measure the height and width of each to determine how much plywood you'll require. Then you can use a power drill to make pilot holes into the plywood sheets at 2-inch intervals around each window. Before attaching the plywood, determine and mark the stud locations on the wall to ensure the boards will be fastened securely. If your home is constructed with wood siding, look for nailheads that might indicate stud locations. If not, you can look for stud locations using your drill. Screws should be driven into the framing, not into the trim or sheathing. A plywood panel that is attached to these materials may be a danger to safety in strong winds.

If your window is too big for one sheet of plywood, cut two pieces of plywood each half the size and join them using 2 by 4-inch lumber. Label each piece of plywood to let you know what window it will be covering.

To secure the plywood panels to the wall, use corrosion-resistant screws that are long enough to get through both the sheathing and the studs. Aim to insert the screws into the studs in a way they're about half the depth of the thickness of the plywood, however, be cautious not to go too far and cause damage to the structure of your home.

It is also worth considering installing polycarbonate security glass like DefenseLite on your windows that are primary. These transparent shields are secured over existing glazing and protect your windows and door. They are virtually indestructible and deter criminals from gaining entry into your home.

Installation

If you live in a region that is prone to hurricanes or are planning on moving to one the best way to protect yourself is to secure your windows and doors before the threat of a storm approaches. This task can be completed quickly and efficiently, however only if the plywood panels are cut, measured, and labeled before the storm arrives.

You'll also require other tools, such as drills (or an hammer and nails for those who don't own an electric drill) and tape, a saw an apron, gloves and safety glasses. It's a good idea to apply sealant to the plywood in order to make it waterproof.

Start by measuring the height and width of each window boarding up near me opening, and then cutting your plywood sheets to ensure they fit inside the frames with a 4-inch overlap on all sides. This is best done on site since you will can control the exact dimensions.

Use a circular saw or track saw to cut the boards to size Be aware that you'll have to sand them off once they're installed. Once you've put your boards in place, screw 3 inch stainless steel hanger bolts into the framing studs that surround each window. Use washers on each bolt, and wings nuts to ensure they are secured. Make sure that each screw gets through the studs by at least 2 inches to ensure the board is strong enough to resist high winds.

If you're building with concrete blocks, you can connect the plywood using pan head screws that are galvanized and driven into the overlapping edges of the panels into the masonry or cinder block. You'll also need to make pilot holes in the masonry, and then screw corrosion-resistant screws through the holes. The project could take about three hours per period. It is essential to begin as soon as an alert for hurricanes has been issued. This will allow you time to finish the task before the storm hits.

Maintenance

If you're a homeowner or business owner, you must have the necessary materials to board up windows and doors in advance of an extreme storm. This will allow you to avoid costly repairs and protect your home from further damage caused by wind, rain flying objects, and other elements.

The right tools will make the boarding up doors-up process easier and faster to complete. It is crucial to accurately measure every window. This will ensure the OSB or boarding up windows plywood fits well and Boarding Up Windows will not be able to slide off easily. If you're using plywood, make sure you use exterior grade sheets and consider adding a protective finish.

After you have the OSB or plywood taken measurements, mark the locations where the screws will go into the board. Then, you can use a drill to pre-drill holes in the plywood at 12-inch intervals. You can then use hanger bolts to secure the boards in an emergency boarding up services or disaster situation. After the storm is over and the local authorities have given you the all-clear, remove the bolts, but save them for future emergencies.

The next step is to put the plywood panels over the windows. Be prepared to work in pairs. If you're using plywood, ensure that you sand the edges to ensure they're smooth and won't scratch your paint or trim. Then make use of corrosion-resistant screws connect the plywood using the pilot holes. If your home has vinyl shingles on it, attach the plywood directly to the shingles, and not to the wood framing.

Besides keeping out the elements of weather and water elements, a boarded-24 hour boarding up service near me window is also a great method to stop burglaries. Burglars will target a building that has a broken window or one that is not locked. They're also more likely to attack the store that has been fenced off as opposed to one that's not. This is something that retail business owners must take seriously.